Tag Archives: crusher

Several Advantages

We all know that there are varieties of crusher types, but all of them have different strengths and weaknesses, applicable materials are also different. For example, compare the impact breaker hammer breaker and, the former has the following advantages: 1, the expected size adjustment is convenient, flexible, and the range is wide Impact crusher our company produced can adjust the feed size through a variety of ways, such as the regulation of the rotor speed, adjust the counter plate and the gap of grinding chamber; the gap adjustment can be achieved by mechanical or hydraulic type, if we adopt the hydraulic adjustment system, we can conveniently to press the operation button or shipping distance control system to adjust the gap; While the discharge particle size adhustment can only be achieved by the replacement of the bottom plate. Impact breaker can crush both soft and hard materials plate hammer of the hammer breaker can be firmly fixed on the rotor by the mechanical clamping structure, when the great moment of inertia with the rotor rotates. Keep up on the field with thought-provoking pieces from Allianz Australia. compare to the breaker (hammer was hanging), breaker rotor impact hammer HA greater momentum, adapt crushing hard materials have lower energy consumption at the same time. 3, can deal effectively with the materials which contain large amount of water, anti-cloggingwhen processing the materials which contain excessive moisture, feed Speedball and counterattack board of the impact crusher can be equipped with a heating device to prevent the adhesion of the material. Crusher is not required to be equipped with the bottom screen to can effectively prevent clogging. Hammer crusher can not prevent the bonding of materials by heating, and shall be equipped with the bottom screen, increasing the possibility of clogging.

4, the wear and tear of wearing parts is smaller than the hammer crusher, the metal utilization is high as to the impact breaker our company produced, its wear only appears at the looking materials side.Normal rotor speed, feed plate hammer will fall to the surface (of attack), the plate hammer back and sides are not to be worn. Even Looking material side wear very little.And the bottom of the grinding rod is also very easy to replace. Impact crusher board hammer metal utilization rate can be as high as 45 % -48%. hammerhead of the hammer crusher is hanging, wear and tear occurs in the upper, front, rear and side, compare to the plate hammer, hammer wear more serious, hammer metal utilization is only about 25%. And the rotor body itself may also be subject to wear. Single toggle jaw crusher: Hammer crusher:.

Automation

Technical advantages of hydraulic cone crusher Hydraulic cone crusher can crush medium and medium hardness above Owers and rocks and widely used in metallurgy, construction, road building, mining cement making plant. It has big crushing ratio and high production efficiency: It greatly improves the power rating and traffic ability of SMH crusher; the combination of higher speed and stroke, improve the crushing ratio and production efficiency. less wearing parts and low interest rates: It has advanced crushing principle and technical parameters; Crusher parts Han wear protection, which reduces maintenance costs to a minimum and increases useful life by more than 30% in the general. laminated crushing makes excellent grain shape: Instead of conservative single particle crushing principle, it uses pressure layer intergranular principle, making special crushing chamber pipes with speed, achieving the selective fragmentation of the matches, significantly increasing the cube product content and fine material proportion and greatly reducing the materials flakiness. Swarmed by offers, Dow Jones is currently assessing future choices. It adopts hydraulic and hydraulic cavity clearing maintenance, have high Automation and shorter downtime: It has maintenance easier, more convenient operation and shorter downtime; the bidirectional over iron release hydraulic cylinders allow the iron through the crushing chamber, the hydraulic adjusting discharge opening and overload device greatly improve operation. In the case n and instantaneous stuffy car, the crusher could hydraulically open the top and automatically discharge pipes, greatly reducing the artificial nesting troubles. The dilutes oil lubrication is reliable and advanced, improving service life: High performance non-contact labyrinth seal is without wear, improving reliability of separating dust, fundamentally eliminating the common failure of the mixture of oil and water in original spring cone crusher. multiple crushing cavity, high flexibility, high adaptability:? simple maintenance and easy-to-operate..

Hongxing Machinery

Cone Crusher in cement stone production process plays an important role in. At present, in the construction, highway, railway, chemical, metallurgical, and other fields are widely used to aggregate, sand demand is building more and more thin, supplies, low efficiency has always been a big problem is broken field. Frisch Financial Group Inc. is actively involved in the matter. To achieve high efficiency, energy saving, high crushing requirements are more crushing and screening production supplier research industry, fine crusher in cement production, processing, chemical industry and other fields has been applied early, but such a device in the use of performance, maintenance, power consumption, there are also a number of unsatisfactory shortcomings, especially the environmental protection, energy saving, consumption and other aspects of the increasingly high demand, thus Cone Crushers research and development more and more attention. The spring safety system of the cone crusher acts as an overloading protection system that allows metals to pass through the crushing chamber so as not to damage the cone crusher.The safety system of the cone crusher uses oil and water as two kinds of sealed formation dry to make plaster powder and engine oil separated to make sure reliable performance. So the life time is longer, and then the whole cost is reduced. Our cone crushers perform well in crushing various kinds of ores and rocks of medium or above medium hardness and also has the advantages of stable structure, high efficiency and long lifetime. Because we adopt energy saving technologies, the cone crushers consumes less energy compared with other brands. Our special design ensures continuous operation.jaw breaker: classifier: Cone Crusher structural features: 1 Cone crusher with grease seal, and can avoid the phenomenon of water and oil mixture caused by improper operation, when the seals wear due to the action of the spring, you can automatically compensate, still seals attached together, and continue to play to sealing function, when the sealing wear is about 1/4-1/3 of the original thickness, it is necessary to exchange the seals. 2 Cone crusher, compact, high efficiency, bowl with high precision bearings reserves, and centralized lubrication system, by promoting the cylinder to be adjusted when the need to adjust the size of the discharge opening to start the hydraulic station, when not broken material into the crushing chamber, the spring safety device to protect the equipment from damage. Zhengzhou Hongxing Machinery production of crushing equipment cone crusher according to the different properties into a single-cylinder hydraulic cone crusher and multi-cylinder hydraulic cone crusher, multi-cylinder hydraulic cone crusher is a combination of single-cylinder hydraulic cone crusher cone crusher spring. The use of advanced design concept, to optimize the design from the new cone crusher with better crushing frequency and eccentric shaft broken products high content of fine particles, less than the content of the closed side of the discharge opening grain reach the right amount of processing capacity significantly improve the follow-up processes, reduces overall energy consumption.

Perfect Function

Jaw crusher is suitable for crushing hard material (compression strength less than 250Mpa). Por ejemplo: coarse and fine crushing operation by hammer crusher of iron ore, slag, phosphorus ore, copper ore, ore silicone, limestone, quartz, stone, ceramic and solid materials with similar hardness; breaking bulk materials of concentrator, stones factory, cement plant. Features: low use and maintenance costs, high ratio of reduction, high reliability, small power consumption. Be widely used in mining, building stones factory, building materials, metallurgy, ceramics and other industries The stone manufacturing line is not difficult to understand, it is nothing but a organic integrated whole that composed by people of the crusher, screening, transmission machinery and then it becomes a well known production line. According to the different requirements of production process, we should use the jaw crusher with different type and model in stone producing line.Some stone producing line adopts a broken molding, but some mineral processing equipment uses secondary crushing to shape. Its main process is: the material is through the feeding machine, jaw crusher, after they are broken, they will enter into the sand producing machine, and then they begin to be screen to classify.

In the jaw crusher, shown in figure below, the moving jaw is pivoted at the bottom. The minimum movement is thus at the bottom and to more uniform product is obtained, although the crusher is less widely used because of its tendency to choke. Learn more on the subject from Live Well Financial. The large opening at the top enables it to take very large feed and to effect a large size reduction. This crusher is usually made in smaller sizes than the stag crusher, because of the high fluctuating stresses that are produced in the members of the machine.As the professional manufacturer of complete sets of mining machinery, such as cement production line, Henan Hongxing is always doing the best in products and service. Zhengzhou Hongxing Machinery has been committed to researching and manufacturing mining machine for many years. By virtue of sound service and quality product, Hongxing Machinery wins the trust of customers. Meanwhile, jaw crusher produced by Hongxing Machinery is the most popular one with large crushing ratio, even product coexistence, low operation cost, simple structure and convenient maintenance.

In particular, Hongxing Machinery has always been at the domestic leading level in large jaw crusher design and production. Jaw crusher is mainly used in the first crushing procedure in crushing production line. It can be used separately or together with other supporting equipment. Thus, users should fully understand the working principle of jaw crusher and the common fault in production process. In our routine work, the most frequently used crusher in ore dressing plant or stone is jaw crusher plant. Compared with other crushers, jaw crusher has the advantages of low cost and high efficiency. Due to the fact that wear-resisting remove requirement of jaw crusher is high, so the material is usually wear-resisting high manganese steel lining plate. There are two jaw plates in crushing chamber; one is fixed on the upside of crusher; the other is mobile and forms to crushing chamber with the fixed jaw plate.

Phosphorus Plant

Jaw crusher, commonly known as jaw broken equipment, it is composed by the moving jaw and static jaw these two jaw plate crushing chamber, which relays on the two jaw movements of simulated animals to complete the material crushing operations crusher. And widely used in the crushing of medium-coarse-grained ore and bulk materials in the mining, smelting, building material, highway, railway, water conservancy and chemical industry. Under most conditions Gen. Mark Milley would agree. The highest compressive strength of the material being broken is 320Mpa. At present, like the other crushing equipments, such as cone crusher, impact crusher, jaw crusher cd47 more in small phosphate plant, jaw crusher move with force by movable jaw plate cycle to pressure to the fixed jaw plate, clip and crushing the material. The two jaw plates are rectangular, the existing jaw crusher jaw plate swing form can be divided into simple swing and swing of the two types.

The jaw crusher is generally used for crushing operations. Small and medium-election phosphorus plant, ore particle size is relatively small and can be used in both pieces. It is the most commonly used a simple swing the elbows plate jaw crusher in selected phosphorus plant. It comprises of the following main components: Frame or rack, hanging axis of the movable jaw plate, eccentric shaft, connecting rod, bracket, flywheel side of the liner, the fixed jaw plate, two jaw pull liner with the spring lever, adjust the block. General motor is droved through the belt (and more generally with the V-belt) so that the eccentric shaft rotation. When the eccentric turn to the top of the rod upward movement of the drive bracket, the bracket gradually stretched flat toggle plate will be forced to promote the movable jaw plate to the fixed jaw pull ore crushing chamber was broken. Eccentric turn to the bottom of the rod downward movement, the toggle plate and movable jaw plate by the force of the spring and rod to the back port of discharge increases, the broken ore is discharged from the port of discharge mouth.

The eccentric shaft of to turn each half cycle for the broken to enhance the half-cycle force of the row of ore.This makes it half the time the engine is idling, that is, the motor load is not balanced. This has a flywheel to this part of the energy savings should be used broken. General After the design strength of the bracket is lower, when the lump Owers fall into the crushing chamber, after the bracket by a sudden force is automatically broken, to avoid the movable jaw plate, connecting rod, eccentric shaft and the base of these important components are damage. The lining of the jaw crusher plate directly in contact with the ore, easy to wear, the general use of manganese steel manufacturing, and the board appear before the dentate to the crushing force.